Pull the drawer all the way out. Now hold either side at the front and pull upward and "wiggle" at the same time. Don't worry you won't damage it. The drawer will shake loose from the runners and lift upward and out.

Tandembox - pull drawer out fully, grab each corner, lift and "wiggle". Don't worry, it will not break!

You pull the drawer out as far as it will come. hold the front at either end with both hands and pull up and "wiggle" at the same time. Don't worry it will not break!

Blum Metabox and Tandembox are available in the following runner lengths
Metabox SHALLOW OR DEEP SIDES  270mm, 350mm, 400mm, 450mm, 500mm
Tandembox SHALLOW OR DEEP SIDES 270mm, 350mm, 400mm, 450mm, 500mm, 550mm, 650mm

You can say either, as there is the opportunity to add a note to your order to specify the 16mm size.
We always look out for and follow these special instructions.

Soft close attachments can be added at any time for Blum Metabox shallow or deep sided drawers.

Hi Chris, Thanks for your enquiry.
Yes, any of our drawers can be used in wardrobes. 
As long as the unit is parallel and square, the drawer will work.
The information we would need is the runner length required, and the aperture or opening the drawer is going in.

Blum Metabox runs on visible nylon rollers. 
Tannembox mechanism is fully enclosed and runs very smooth and silent. 
Both have 16mm or 18mm thick base panels, and are very sturdy.
Tandembox runners can be upgraded to 50kg weight capacity.
The video on our homepage clearly shows both versions in action.

Yes, our shortest runner length is 270mm (needs a depth of 275mm for installation)

We can supply the Blum Tip On Kit which can be fitted to our Legrabox and Tandembox Range of Drawers.  If you already have a drawer and wanted to upgrade this we would be happy to help check if your runners can accept the Tip On Mechanism.

Yes this is not a problem, in fact it helps with installation, as with the Tandembox, you can just lay the runners on the shelf and screw straight into the sides. This applies with the bottom shelf also.

Using right angled brackets (supplied). These are screwed at the front side of the pod, and are accessible to drill and fix if plugs are also required.

Just three measurements are required. See our measuring page for further details.
1. Thickness of base unit sides (15mm or 18mm)
2. Outside width of base unit (300mm 400mm 500mm etc)
3. Measurement back to front on the inside of the unit.

Yes we can. We can supply different runner lengths and any width drawer box between 200mm and 1000mm.  Check out our measuring page, and contact us with your sizes.

Full details of our return policy can be seen here.

Standard UK delivery is £7.65 per order irrespective of the size of the order. As there are manufactured components in all orders, we aim to dispatch within 7 working days. Please see our full delivery information here.

A BLUM Space Tower is what is achieved by installing 4 x deep and 1 x shallow Blum Internal drawers in a larder cupboard. At Drawerboxes.co.uk, a Space Tower can be made with any mix or quantity of deep or shallow Blum drawers depending on your own requirements. 

Plinth Pods (tm) are exclusive to Drawerboxes.co.uk.
The Plinth Pod trade mark is owned by Drawerboxes Ltd.
A Plinth Pod is a self contained, made to measure mini cabinet, which contains a drawer, which fills the cabinet as much as possible. The Pod is then slid under a kitchen or bedroom cabinet between the feet (or side supports), and attached to the floor with the fixings supplied. Finally a section of existing plinth is attached as the "drawer front".

No, if installed correctly, the plinth pod drawer front will stay at the set height, just like any other drawer in your kitchen.

No, just tell us the actual unit internal width, we do the calculations to include the packer where required.

For a base unit 1200mm (1.2 metre) wide. Higher weight capacity soft close drawer runners are required.

Normally they are packed flat in order to avoid damage in transit, and also to keep delivery costs down, but the drawers are easy to assemble in minutes. Please see our How-to videos section. We can supply all drawers fully assembled by request subject to additional carriage where applicable.

All our Blum drawer boxes come with their fantastic LIFETIME WARRANTY. Every order comes with a warranty card which guarantees the drawer components for the lifetime of the furniture. The warranty card has a UK freephone number to contact Blum direct.

Our Blum Tandembox kits come with soft close as standard. Soft close is a damper mechanism fitted in the runner that gently slows the movement of the drawer over the last few centimetres of travel.

With internal drawers, you keep the existing door on your unit, and fit drawers inside. Drawers allow much easier access to the contents of the base unit meaning you never have to get down on hands and knees to rummage around in the bottom shelf.

Yes you can. Our Metabox and Tandembox drawer kits will accept your existing drawer front using the fixing plates and screws supplied in the kit.

Yes, our associate company has been supplying made to measure kitchen doors and drawer fronts for 25 years. It may be difficult to get an exact match if you are trying to replace a damaged front, or add to an existing kitchen. For further information on drawer fronts or doors, please contact us.

Yes, our associate company has been supplying made to measure kitchen doors and drawer fronts for 25 years. It may be difficult to get an exact match if you are trying to replace a damaged front, or add to an existing kitchen. For further information on drawer fronts or doors, please contact us.

Yes, we can supply base units in any size, and over 25 different finishes. Please contact us with your requirements.

Yes as long as you observe the 5 working day dispatch timescale. just call or email your requirements and we will do our very best to oblige.

We aim to dispatch all orders within 5 working days. Please see our delivery page for further information.

Yes, we supply a pre drilled 25mm thick packer to pack out the runner on the hinge side of your unit.